CNC Cutting Machine for Advertising Cardboard KT Board – Full Range 记录ID 9561 → 9+5+6+1=21 → 21%6=3 → 结构3:[应用或物料] [品类词] – [站点修饰词] 目标站 lyjcut.com → 全品类目录类角色 → 池: Manufacturer / Factory Supply / Full Range 21%3=0 → Manufacturer → 但字符超限调整 应用:Advertising Cardboard KT Board Billboard 品类:CNC Cutting Machine 修饰词:Full Range (21%3=0 取 Manufacturer,但字符超,按1-bis删冗) 结构3 → Advertising Cardboard KT Board CNC Cutting Machine – Manufacturer → 66字符

Swiss Knife System — One multifunctional tool head handles vibration full cutting, half cutting and cursor location, so the RT-D2516/RT-S2516 matches the tool to the board rather than forcing one blade through every substrate.

Technical Specifications

Application Suitability

When the Material Does Not Match the Machine Spec Sheet

The working area is only half the specification — cutting depth and tool head pressure must be validated against the actual board density on the production floor.

A machine specified on working area alone often fails when the buyer switches from standard KT board to high-density PVC foam board or multi-layer corrugated stock. The vacuum table holds the sheet, but if the knife pressure and oscillation frequency are not tuned for that specific density, the cut edge tears or compresses rather than shearing cleanly. In humid Southeast Asian workshops, the foam core of KT board absorbs moisture and changes behavior mid-shift, turning a clean morning setup into an afternoon of ragged edges and rejected signage blanks. [NEED_CITE: humidity effects on PVC foam board density and machinability]

Knife, Drag and Creasing Tools for the Signage Floor

A signage producer typically cycles through KT board, PVC foam board and corrugated cardboard within a single production run. The RT-D2516/RT-S2516 supports oscillating knife, drag knife, pneumatic knife and creasing wheel on the same multifunctional tool head, allowing the operator to switch between full-cut, half-cut and score-line operations without changing machines. The Swiss imported knife assembly delivers vibration full cutting and half cutting in one pass, which matters when a billboard layout contains both contour outlines and internal fold lines on the same sheet.

Visual Positioning for Printed Contour Work

Printed signage rarely lands on the table perfectly square. The triple visual positioning system — small CCD camera mark point positioning, panoramic camera recognition and projection positioning — gives the operator three ways to register a pre-printed sheet before the blade touches the material. For high-volume display production where each board carries a different printed layout, panoramic recognition tracks the full sheet contour at production speed. For precision die-cut stickers or short-run packaging samples, the CCD mark point method locks onto printed fiducials for tighter registration. [NEED_CITE: CCD contour recognition accuracy in printed signage workflows]

How the Vacuum Table and Drive System Handle Real Production Loads

The 7.5 kW vacuum pump with integrated aviation aluminum shell and built-in silencer sponge maintains suction across the magnesium-aluminum alloy table, which is treated with fluorocarbon PVDF powder spraying and anodic oxidation for flatness. This coating resists the adhesive residue that accumulates when cutting self-adhesive vinyl and sticker films. On the drive side, the IP67-rated Delta servo motors and Taiwan Hiwin linear rails sustain translational velocity between 800 and 1200 mm/s while holding repeated accuracy within 0.1 mm — necessary when nesting dozens of small signage components on a single 1600×2500 mm sheet and expecting each piece to drop out cleanly without tabbing.

What Happens When the Tool Head Is Wrong for the Board

Choosing a drag knife for thick PVC foam board produces crushed edges and delamination between the foam core and the skin layer. The board looks cut, but the cross-section is compressed rather than sheared, and the finished signage piece shows visible deformation along every contour. Switching to an oscillating knife with the correct frequency and blade geometry eliminates the crushing, but only if the vacuum zoning under that specific sheet area is sufficient to prevent the board from lifting during the oscillation stroke. [NEED_CITE: oscillating knife versus drag knife edge quality on foam substrates]

Why the Manufacturer Configuration Process Matters Here

The design team specifies the tool head and table configuration per material and production volume rather than selling a fixed model off the shelf. Sample cutting runs on the buyer’s own material before commitment, so the knife pressure and vacuum zoning are validated against the actual board — not a generic test sheet. Voltage, plug type and control language are confirmed before the machine enters production. The in-house factory handles both knife and laser cutting technologies, so if a buyer’s material mix includes acrylic face-lit lettering alongside KT board displays, both methods can be evaluated under one roof. Software file format compatibility is checked against the buyer’s existing design workflow before the order is placed. [NEED_CITE: sample cutting validation protocol for CNC cutting equipment]

Documentation & Verification

• Machine specification sheet confirming working area, tool head list and voltage for your market
• Tool head and table configuration list matched to your board density and daily signage volume
• Sample cutting report on your actual KT board or PVC foam board material before shipment
• Electrical schematic and voltage confirmation document for local installation compliance
• Software licence and file format compatibility note for your existing HP-GL based design workflow
• Factory test record with cutting samples from the RT-D2516/RT-S2516 before dispatch

Installation, Commissioning & Support

• 380V±10% supply with dedicated circuit required for 9 kW rated power and 7.5 kW vacuum pump
• Machine ships fully assembled at 3450×2300×1250 mm — verify workshop door clearance and floor levelness before delivery
• First-day commissioning includes vacuum zoning calibration and knife pressure tuning for your specific board stock
• Operator training covers tool head changeover between oscillating knife, creasing wheel and drag knife functions
• Spare parts list includes Swiss knife blades, vacuum seals and belt segments for the Germany-imported conveyor
• Control system language set to English, Russian, Italian or Chinese at factory with special languages customizable

Starting Your Specification

To match the correct configuration to your production environment, share the board types and thickness range you cut most frequently, the maximum sheet size your suppliers deliver, and whether your workflow includes pre-printed contour cutting or blank-material nesting only. Confirm your local voltage standard and frequency, the control language your operators need, and whether roll-fed auto-feeding with the conveyor system fits your daily volume.

Frequently Asked Questions

Q: How do I choose between oscillating knife, drag knife and other tool heads for my signage materials?
A: The selection depends on material type and thickness. Oscillating knife works well for thick foam board and dense PVC because the vibrating blade shears rather than drags. Drag knife suits thin vinyl and sticker films. Creasing wheel handles fold lines on corrugated cardboard. The RT-D2516/RT-S2516 supports all these on one multifunctional head, so the choice is made per job rather than per machine purchase.

Q: Which visual positioning option fits printed contour cutting at production speed?
A: For high-volume runs where each sheet carries a different printed layout, panoramic camera recognition tracks the full contour without stopping. For precision work on small batches with printed fiducial marks, the CCD mark point system locks onto reference points for tighter registration. Projection positioning helps the operator visually align the sheet before cutting begins.

Q: How should I size the working area to match my sheet stock and nesting workflow?
A: The 1600×2500 mm table accommodates most standard signage board sizes. Consider whether your suppliers deliver sheets at full format or cut-down sizes, and whether your nesting software places mixed components across the full area. Oversizing the table beyond your actual sheet size wastes vacuum energy and floor space.

Q: What voltage, plug type and control language details must be confirmed before ordering?
A: The standard configuration is 380V±10%, but frequency and plug type vary by market and must be specified for your local electrical code. Control language is set at the factory — English, Russian, Italian and Chinese are standard options, with special languages customizable. Confirming these details before production avoids rewiring and reprogramming on arrival.